Sometimes a Cigar Is More Than Just a Cigar

September 10, 2014

As a chemical engineer, I can’t just smoke a cigar and leave it at that. Here, I investigate the anatomy, structure, and chemical process zones of a cigar and show you a simple model of the temperature distribution of the smoke in a cigar as well as the concentration of oxygen.

A Cigar’s Anatomy, Structure, and Process Zones

Anybody who smokes a cigar every now and then recognizes the feeling of sharpness and alertness from the first few puffs, enhanced later by the calm and tranquility supplied by the following ones. Health issues aside, smoking a cigar can, in my opinion, sometimes be the best way to achieve serenity and contemplation.

In those moments of maximum alertness, I usually check that I get a straight burn line. Sometimes, this makes me think about combustion and the transport and reactions in the cigar. When calmness sets in, I usually admire the pattern of the smoke and, then, sometimes reflect about its fluid mechanics.

The schematic below shows the cigar’s anatomy with the head, body, foot, and cap; its structure with the filler, binder, and wrapper leaf; and the zones for the different processes that take place in the cigar during smoking, such as the combustion, pyrolysis, and condensation zones (references in the “Further Reading” section).

Image showing the structure and process zones in a cigar.
The anatomy, structure, and different process zones in a cigar. The core of the cigar is the filler, and the binder helps to keep the structure of the cigar, while the wrapper leaf envelops it. The cap is cut off before smoking. A thin straight burn line is desired.

After ignition, when the cigar has reached a pseudo-steady state, a combustion zone forms. A pyrolysis zone forms just behind the combustion zone.

Chemical Processes in a Burning Cigar

Oxygen that is transported to the combustion zone, through convection and diffusion during a puff and through diffusion between puffs, is consumed in the combustion process. Therefore, only oxygen-depleted gases reach the zone behind the combustion zone, where pyrolysis occurs. In this zone, thermal decomposition of the organic compounds in the tobacco leaves takes place in the absence of oxygen. Some of the products of pyrolysis vaporize, while others remain to be further oxidized later in what is going to become the combustion zone, as the combustion and ash zones move toward the head of the cigar. This means that distillation also occurs in the pyrolysis zone.

During a puff, vaporized products from the pyrolysis zone follow the smoke towards the head of the cigar. As the smoke travels to the head, it is cooled and filtered by the cool tobacco. Condensation of some of the compounds in the smoke is triggered by the decreased temperature, forming an aerosol. The small droplets that are formed contain the nicotine and a lot of the flavors of the mainstream smoke. Some dilution of the smoke occurs due to air leaking through the wrapper as well as some leakage of carbon monoxide out of the cigar. However, both of these processes are very slow, since the wrapper leaf is not very permeable to gas.

Also, note that the porosity is different for the filler tobacco, binder, and wrapper leaf. The porosity determines the shape of the combustion and pyrolysis zones.

What Affects the Cigar’s Shape

The shape of the combustion zone further determines the shape that the cigar takes on as you smoke it. During a puff, the combustion process close to the wrapper of the cigar is accelerated due to the high transport of oxygen around the edges. Between puffs, the edges are better cooled by the ambient air, the temperature distribution becomes more uniform, and the distribution of combustion to the middle of the cigar makes the combustion zone more uniform.

If the cigar is smoked too quickly, you’ll end up with coning, where the edges of the cigar are consumed faster than the middle. On the other hand, if the cigar is smoked too slowly, then tunneling occurs. Why? Because the middle of the cigar burns quicker between puffs due to the ambient air cooling the edges better. Imperfections in the ignition and structure of the cigar may also cause other effects of nonuniform combustion, such as canoeing and runners (read more on burn issues here.)

Personally, I think that tunneling is the worst problem, since it seems to lower the temperature, producing less and poorer quality smoke.

Cigar Simulation

Below are the results from a simulation of a relatively simple model of a cigar during a puff and between puffs. The model describes the combustion and formation of carbon, in addition to the pyrolysis of tobacco. We also included the transport of oxygen, smoke, and nitrogen in the model. Of course, in reality, the process is much more complex from a chemical engineering perspective, but the model provides a nice and simple view of the temperature distribution in the smoke and oxygen concentration.

The temperature distribution of smoke.
The oxygen concentration in a cigar.
Temperature distribution of the smoke in a cigar (top) and concentration of oxygen (bottom). The oxygen concentration dramatically decreases in the combustion zone during a puff. Leakage through the wrapper contributes only to a small extent. The combustion of carbon is a classic example of a shrinking core problem in reactions engineering.

Do Not Inhale Cigar Smoke

When the constituents of cigar smoke dissolve in the mouth, the saliva becomes alkaline. In contrast, cigarette smoke makes saliva acidic. At low pH, nicotine is protonated and is, therefore, neutral in charge. On the otherhand, at high pH, nicotine loses the proton and becomes negatively charged. The negatively charged ion of nicotine is able to pass through the membranes in the mouth much easier than the neutral form, which is repelled. For this reason, cigar smoke does not need to and should not be inhaled; nicotine is absorbed and transported into the blood just by the uptake in the mouth.

As mentioned earlier, once the first dose of nicotine has done its work by accelerating and stimulating thought, then the increased levels of nicotine replace the initial activation with serenity. This chain of events is referred to as Nesbitt’s paradox, after the scientist who first put his finger on it.

More Than Just a Cigar

In case you didn’t pick up on it, the title of this blog post is a play on the quote (or misquote, to be exact) “sometimes a cigar is just a cigar”. The original quote refers to Sigmund Freud’s answer to the insinuation that his constant cigar smoking had phallic symbolic meaning, as implied by Freud’s own theory (if you’re unfamiliar with the theory, read more here and here.)

Cartoon depiction of smoking.

The complex processes involved in cigar smoking and the beautiful smoke patterns show that, phallic symbolism aside, sometimes a cigar actually is more than just a cigar…

Further Reading

  1. R.R. Baker, “Mechanisms of Smoke Formation and Delivery”, Tobacco Chemists’ Research Conference Symposium, 1980.
  2. Cigarette combustion science“.
  3. P. Ermala and L. Holsti, “On the Burning Temperatures of Tobacco”, Cancer Research,16:490-495, 1956.

Disclaimer: COMSOL does not endorse smoking, just investigative science and simulating everyday scenarios where multiphysics is at play.


Comments (3)

Leave a Comment
Log In | Registration
Loading...
Koti Rao
Koti Rao
May 24, 2017

Hello Mr. Ed Fontes, This is really a excellent explanation on this subject. I am a new bie to comsol and would like to understand and solve the complex combustion process involved in cigarette. Could you please share the file that has been created by you, so that it would be of great help to start with.

Thank you in advance.

Koti Rao
Koti Rao
May 24, 2017

Hello Mr. Ed Fontes, This is really an excellent explanation on this subject. I am a new bie to comsol and would like to understand and solve the complex combustion process involved in cigarette. Could you please share the file that has been created by you, so that it would be of great help to start with.

Thank you in advance.

Bridget Cunningham
Bridget Cunningham
June 27, 2017 COMSOL Employee

Hi Koti,

Thank you for your comment.

While this specific model file is not available for download, we encourage you to direct any modeling questions you may have to our Support team.

Online Support Center: https://www.comsol.com/support
Email: support@comsol.com

EXPLORE COMSOL BLOG